Solid
plate construction,
enclosed stroke system. |
Easy
installation with locking bolts.
Custom fit. |
|
Triple stops. Robust, stabile
and for long unsupported
lengths. Ideal for tough ambient
conditions (dirt) and outdoor
applications (such as crane
systems). |
The side plates are connected with
locking bolts. This makes it
easy to install and disassemble
the carrier. Cross-bars can be
fil |
With the MC
1300, the push and pull forces are
transmitted via the optimum link design for
this purpose. As a result link wear is
reduced to a minimum and the service life of
the cable carrier is considerably
lengthened.
 |
 |
-
Force transmission with a
pin-hole joint.
|
-
Force transmission for the
MC 1300 with the "life
extending 2 disc principle".
|
|
The MC 1300 stay
systems have additional advantages:
-
maximum flexing strength with minimized
weight
-
minimized cable abrasion due to low friction
between aluminum frame stays and conventional
cable and hose jacket materials
 |
 |
-
Stay variant
RMF – stays affixed to each side
with 1 screw. Inside/outside: stays
can be quickly released for laying
cables.
|
-
For extreme applications with chain
widths up to 800 mm, the proven
solid frame stay RM is available
that can be screwed with 4 screws.
|
With the divider
systems for the MC 1300, you can organize the inside
of the cable and hose carrier:
-
Standard dividers for vertical and continuous
horizontal height subdivision.
-
Partition systems made of plastic or aluminum
for more challenging separations.
 |
 |
 |
Divider system TS 0
with
standard vertical dividers |
Divider system TS 1
with additional continuous
height subdivision. |
Divider system TS 3
with plastic or aluminum
partitions. |
Ideal for
long travel lengths
Replaceable glide
shoes for gliding arrangements.
In the case
of cable carriers in gliding
arrangement, the gliding surfaces are
exposed to particularly heavy loads.
At high travel speeds, when
contamination exists or when there is a
high number of travel cycles, highly
abrasion resistant glide shoes can be
used.
This can practically double the service
life of the carriers since only the
glide shoes have to be exchanged when
there is wear in the gliding area.
Otherwise the entire cable carrier has
to be exchanged.
|
 |
-
Fast assembly of the glide shoes.
|
Roller holder for use in the Rail Cable Carrier –
RCC
As with all other types in the M Series, the new MC
1300 is ideal for use in our new Rail Cable Carrier
(RCC) roller system for extremely long travel
lengths over 500 m (see Rail Cable Carrier – RCC).
A reliable solution for the applications on their
side
Also highly suitable
for applications where the carrier is installed on
its side and for extreme transverse accelerations
(fixable dividers with RMF stay variants).
 |
 |
-
Fixing on both sides (in 4 mm steps)
ensures that the dividers have a
secure hold.
|
-
The fixing profiles are simply
pushed into the stays.
|
Easy connection with integratable C-rails for strain
relief elements
|
UMB
(Universal Mounting Brackets) made of
plastic
With the UMB
(Universal Mounting Brackets), you can
connect the MC 1300 very easily from „above,
below and at the front“. The open
construction ensures optimum accessibility
and easy and quick installation. |
 |
-
UMB (Universal Mounting Brackets
Inside open for easy and fast
installation.
|
|
Strain relief
devices.
The C-rails are
fixed together with the end connectors and
do not have to be screwed separately.
Different C-rails are available with slot
widths of 11 and 17 mm. |
|
-
UMB (Universal Mounting Brackets
Inside open for easy and fast
installation.
|
Back to MC 1300 overview |
